Skip to Content

AM2315 I2C temperatur-fugtighedssensor (i kabinet)

Varenr: H28076
EAN: 5705412280761
https://bogholderi.el-grossisten.dk/web/image/product.template/193540/image_1920?unique=ed5b73f

Endelig har vi en I2C-interface temperatur og fugtighed sensor i en praktisk lukket stil. Denne sensor indeholder en termistor temperaturføler og en kapacitiv fugtighedssensor. En lille mikrocontroller indeni klarer aflæsningerne og giver et simpelt I2C interface til at læse de færdige og kalibrerede output data. Specielt flot er det, at denne sensor er i et robust kabinet med monteringsbeslag, hvilket gør det langt bedre end en normal PCB-monteret sensor.

Selvom den ikke er angivet som "vejrbestandig", ville denne sensor fungere meget bedre, i vind og vejr, end PCB-breakout sensorer, og i2c interface gør det lettere at forbinde med mikrocomputere. Du skal blot slutte den røde ledning til 5V strøm, sort til jord, gul ledning til din i2c data pin og den hvide ledning til i2c clock pin. Du kan ikke ændre i2c-adressen, så kun én sensor pr. I2c-bus. To 10 kOhm pullup modstande er nødvendige til brug (medfølger ikke - se tilbehør)), tilsluttes fra SDA og SCL linjer til strømkablet.

Tekniske detaljer:

  • 3,5 til 5,5 V strøm og I / O
  • 10 mA maks. strømforbrug under konvertering (mens der anmodes om data)
  • God til 0-100% luftfugtighedslæsninger med 2% nøjagtighed
  • God til -20 til 80°C temperaturaflæsninger ± 0,1°C nøjagtighed
  • 0,5 Hz opdateringshastighed
  • Husstørrelse: 98mm x Ø16mm
  • 4 ledninger: 50 cm lange
  • Vægt: 83g
  • Dette kort/chip bruger I2C 7-bit adresse 05C
  • Se Adafruits produkthjælp

Finally we have an I2C-interface temperature & humidity sensor in a nice enclosed style. This sensor contains a thermistor temperature sensor and a capacitive humidity sensor. A small microcontroller inside does the readings and provides a simple I2C interface for reading the finished & calibrated output data. Especially nice is that this sensor is in a rugged case with mounting bracket, which makes it way superior to a normal PCB-mounted sensor.

While it is not rated as 'weatherproof', this sensor would do much better for sensing where there might be wind, rain, zombies, etc. than SHT PCB-breakout sensors, and the i2c interface makes it easier to interface with microcomputers that can't do the delicate timing of the DHT sensors.

Simply connect the red wire to 5V power, black to ground, yellow wire to your i2c data pin, and the white wire to the i2c clock pin. You cannot change the i2c address so only one sensor per i2c bus. Two ~10 kOhm pullup resistors are required for use, connect from the SDA and SCL lines to the power wire, the pullup resistors are not included!

Specifications:

  • 3.5 to 5.5V power and I/O
  • 10 mA max current use during conversion (while requesting data)
  • Good for 0-100% humidity readings with 2% accuracy
  • Good for -20 to 80°C temperature readings ±0.1°C typical accuracy
  • 0.5 Hz update rate
  • Body size: 98mm x Ø16mm
  • 4 wires: 50cm long
  • Weight: 83g
  • This board/chip uses I2C 7-bit address 05C
  • Se Adafruits produkthjælp
Læs mere

DKK 229,00 229.0 DKK DKK 229,00 Moms Inkluderet

Not Available For Sale

Denne kombination eksistere ikke.

0.0 Stk på lager
0.0 Stk på fjernlager